Z-class Melbourne tram

From Infogalactic: the planetary knowledge core
(Redirected from Z class Melbourne tram)
Jump to: navigation, search
Z-class
250px
Z3 139 on Swanston Sreet, Carlton in PTV livery in December 2013
Manufacturer Comeng
Assembly Dandenong
Constructed 1975–1983
Number built 230
Number in service 146
Fleet numbers 1-230
Depots Brunswick
Essendon
Glenhuntly
Malvern
Specifications
Length Z1/Z2: 16.00 m (52 ft 6 in)
Z3: 16.64 m (54 ft 7 in)
Width 2.67 m (8 ft 9 in)
Height Z1/Z2: 3.55 m (11 ft 8 in)
Z3: 3.41 m (11 ft 2 in)
Weight Z1/Z2: 19 t (19 long tons; 21 short tons)
Z3: 21.8 t (21.5 long tons; 24.0 short tons)
Passenger capacity seats Z1/Z2: 48
Z3: 42
Passenger capacity standing 70[1]
Doors Z1/Z2: 4
Z3: 6
Traction motors Z1/Z2: 4 x ASEA LJB 23/2 57 kW
Z3: 2 x AEG ABS 3322 195 kW
Power supply N/A
Electric system(s) 600 V DC catenary
Current collection method Pantograph
Bogies Z1/Z2: ASEA/GS type 28
Z3: Duwag
Gauge 1,435 mm (4 ft 8 1⁄2 in) standard gauge

The Z-class are single-unit bogie trams that operate on the Melbourne tram network. Between 1975 and 1983, 230 trams spanning three subclasses were built by Comeng, Dandenong. The design was based on two similar Gothenburg tram models, and a prototype built by the Melbourne and Metropolitan Tramways Board. While the Z1 and Z2-class trams were very similar, the Z3-class had significant design changes.

Since introduction they have had a variety of liveries, and modifications. Today many Z1 and Z2-class trams have been retired, with 146 Z-class trams remaining in service, 114 of which being Z3-class trams.

History

File:Göteborgs Spårvägar AB tram 818+731.JPG
Gothenburg, M29 (front) and M28 (rear) trams, the inspiration for the Z-class tram
Z1 95 in Metropolitan Transit Authority livery on Swanston Street in September 2006
File:Z1 78 on St Kilda Road.jpg
Z1 78 on St Kilda Road in February 2013
File:Z1-class Melbourne tram interior, 2013.JPG
Interior of a Z1-class in December 2013
Z2 101 on Swanston Street in October 2012
Interior of a Z3-class in November 2013
Refurbished Z3 183 in December 2009

When Melbourne and Metropolitan Tramways Board (M&MTB) staff were sent to Europe in 1965 to investigate other tramway operations, they took interest in Swedish trams, and upon return in 1966 drew up specifications, and had a timber mockup built. This mockup was to be the basis for a new tram design for Melbourne. The M&MTB approved of the design, and in 1972 requested a prototype be constructed, the result was PCC 1041 being built at Preston Workshops. It was 'European in appearance' and utilised components bought new, and recycled from an earlier prototype tram, PCC 980.[2]:195–196 Prototype PCC 1041 became the basis of the Z-class trams, with 230 trams – influenced by the Gothenburg, Sweden M28 and M29 design – built by Comeng, Dandenong between 1974 and 1983.[2]:197[3][4]:32

When the Melbourne tram network was split in preparation for privatisation, all Z-class passed to M>Tram. All passed to Yarra Trams in 2004, where they were refurbished and repainted into Yarra Trams livery.[5] In late 2007, the remaining Z-class trams with analogue signage were refitted with digital signage, replacing the original flap and rolling route destination displays.[6] The Z-class trams are primarily in Yarra Trams or all-over advertising livery, although the Z3-class are progressively being refurbished and repainted in Public Transport Victoria livery.[7][8][9][10]

On 26 October 2011, a Z3-class tram (no. 158), specially liveried as a Royal Tram was used to convey Queen Elizabeth II and Prince Philip along St Kilda Road from Federation Square to Government House during their visit to Melbourne. The Royal Tram was in regular service until February 2013.[11][12][13][14]

Subclasses

Z1-class

In 1972 Rupert Hamer became Premier of Victoria, promising new trams, which had been highlighted as needed in the 1969 Melbourne Transportation Plan. Comeng, in anticipation of a tender, dispatched workers to Europe who, knowing of the fondness within the M&MTB of the Swedish tram design, acquired the plans for the Gothenburg M29 tram from Hägglund & Söner. It was understood that ASEA would supply the electrical equipment, as they had been involved in the supply of equipment for the Gothenburg M28 which was almost identical to the Gothenburg M29 trams, and had recently acquired the rolling stock division of Hägglund & Söner.[2]:196–197

Tenders for 100 trams based on prototype PCC 1041's design were called for in 1972 with Comeng awarded a contract in 1973. The plans purchased by Comeng proved to be less useful than anticipated, due to them being metric, single ended (with doors only on one side), and to some extent 'over-designed'. Comeng essentially started anew, but retained elements of the structural design and ASEA as the electrical equipment supplier, who would supply equipment from the Gothenburg M28 design.[2]:197–198

There were a number of design changes made which differentiated the Z-class from PCC 1041, including the destination display arrangement.[2]:198 Internally they, like PCC 1041, had conductors consoles that passengers would have to queue for, and only two doors per side, these two features hampered loading and proved unpopular.[2]:196[3] Fitting the ASEA M28 equipment into the Z-class body, which was heavily based on the M29, posed a problem due to the extra doors, tapered ends, and second cab Comeng had added to make them able to operate in Melbourne, this necessitated lengthening the design to accommodate the equipment.[2]:199

Construction started at Comeng Dandenong in 1974, with Dandenong's workforce tripling to cope with the order.[2]:199–200 The first Z1-class tram was delivered in December 1974, and the last in May 1978.[2]:203 Major construction was carried out at Dandenong, with bogie frames fabricated at Granville, and final fit out and commissioning occurring at the M&MTB's Preston Workshops.[2]:199–200, 202

Soon after commissioning it became apparent that the Z-class had ride problems due to stiff suspension, and track differences between Gothenburg and Melbourne. The issues were rectified by the time the 80th tram was constructed, and the fix, rubber secondary suspension, was retrofitted to all trams. The braking systems also had issues, and were seen as insufficient by the M&MTB.[2]:203[15]:31

In anticipation of the Z3-class contract a Z1-class was fitted with chopper control in 1977 for evaluation purposes. Although it was converted back later, the test successfully demonstrated chopper control trams could operate on the Melbourne tram system without causing interference, and all Z3-class trams were fitted with chopper controls.[15]:31

Most of Z1-class were withdrawn following the introduction of the C and D class trams in 2001/02, leaving 29 in service. Those withdrawn were usually sold at auction, with some being donated to tram museums;[7] four have been preserved.[16] Their internal refurbishment had less refurbished features than Z3-class, only seat pads and grab rails/anchors were replaced.

In 2003, the Z1 trams were taken to Brooklyn Sims Metal for scrapping after their permanent withdrawal.

In 2006, Z1 81 advertise the Festival for the Melbourne Commonwealth Games and last run in March 2007 and transferred to Preston Workshops for the permanent storage.

On 22 December 2014, Z1 1, Z1 4 and Z1 14 were withdrawn to Preston Workshops from Malvern and Glenhuntly depot.

In February 2015, the Z1 trams are withdrawn extra 46 trams and remaining 22 Z1 trams to be in service.

Z2-class

Between June 1978 and February 1979, 15 Z2-class trams were built as an extension of the Z1-class order. These have few differences from the Z1-class built earlier.[2]:203[3] Most Z2-class trams have been withdrawn from service, with two remaining in service.[8]

In 2008, Z2 101 were returned to service after their storage at Preston Workshops and as of now, Yarra Trams operates the 3 remaining Z2 trams. Z2 trams had remained in 2 fleets currently in service for Yarra Trams in 2015.

Z3-class

A tender for 100 new trams was called by the M&MTB in early 1977, Ansair, Comeng and Siemens tendered. Although Comeng originally planning on using ASEA control equipment, as in the Z1 and Z2-class, they opted to give the M&MTB a variety of options, leading to 28 different possible configurations of control equipment, bogies, and suspension types. Comeng were ultimately selected, and between 1979 and 1983, 115 Z3-class trams were built.[15]:31–36

Although externally very similar to the preceding Z1 and Z2-class trams they had significant design differences, and were a significant improvement on the Z1 and Z2-class trams.[15]:31–36[17] They are fitted with AEG control equipment and Duewag bogies, have an additional door each side (for a total of three rather than two for the Z1 and Z2), drop down (as opposed to top sliding) Beclawat windows and improved headlights. They also had much smoother acceleration and braking performance, and improved suspension. The Z3-class build process went smoothly, with few problems, bar a slow delivery of equipment from AEG, and a few minor faults that required remedying after construction.[3][4]:32[15]:31–36

In mid 2013 funding was provided from Public Transport Victoria to Yarra Trams for the refurbishment of the Z3-class trams. All 114 Z3-class trams will receive new seats, painted interior walls, glass replacement with scratch proof film applied, and the Public Transport Victoria livery at Preston Workshops. Funding of $15.7m has been provided.[10]

Today 114 remain in service, Z3 149 was scrapped after being destroyed in a fire. All are currently in either Yarra Trams, Public Transport Victoria, or all-over advertising livery. The trams operate from Brunswick, Essendon, Glenhuntly and Malvern depots.[9]

Use

The Z1/Z2-class operate on the following routes:

The Z3-Class operate on the above routes as well as the following:

References

  1. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 2.11 Lua error in package.lua at line 80: module 'strict' not found.
  3. ↑ 3.0 3.1 3.2 3.3 Lua error in package.lua at line 80: module 'strict' not found.
  4. ↑ 4.0 4.1 Lua error in package.lua at line 80: module 'strict' not found.
  5. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  6. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  7. ↑ 7.0 7.1 Z1 Class Vicsig
  8. ↑ 8.0 8.1 Z2 Class Vicsig
  9. ↑ 9.0 9.1 Z3 Class Vicsig
  10. ↑ 10.0 10.1 Lua error in package.lua at line 80: module 'strict' not found.
  11. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  12. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  13. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  14. ↑ Z3.158 Vicsig
  15. ↑ 15.0 15.1 15.2 15.3 15.4 Lua error in package.lua at line 80: module 'strict' not found.
  16. ↑ Lua error in package.lua at line 80: module 'strict' not found.
  17. ↑ Lua error in package.lua at line 80: module 'strict' not found.

External links

Media related to Lua error in package.lua at line 80: module 'strict' not found. at Wikimedia Commons

Retrieved from "https://infogalactic.com/w/index.php?title=Z-class_Melbourne_tram&oldid=3697409"